HOMEAchievements - Journal papers
Achievements
Journal Papers
【A01ア】
- "Change in Microstructures and Mechanical Properties during Deep Wire Drawing of Copper"
K.Hanazaki, N.Shigeiri and N.Tsuji
Mater. Sci. Eng. A, Vol.527, Issues 21-22 (2010), pp.5699-5707.
- "Friction Stir Welding of High Carbon Steel with Excellent Toughness and Ductility"
Y.D.Chung, H.Fujii, R.Ueji and N.Tsuji
Scripta Mater. 63 (2010), pp.223-226.
- "New Routes for Fabricating Ultrafine Grained Microstructures in Bulky Steels without Very High Strains"
N.Tsuji
Adv. Eng. Mater., Vol.12, Iss.8 (2010), pp.701-707.
- "Evolution of Deformation and Recrystallization Textures in High Purity Ni and Ni-5at.%W Alloy"
P.P. Bhattacharjee, R.K.Ray, N. Tsuji
Metall. Mater. Trans. A, Vol.41 (2010), No.11, pp.2856-2870.
- "Change in Electrical Resistivity of Commercial Purity Aluminum Severely Plastic Deformed"
Y.Miyajima, S.Komatsu, M.Mitsuhara, S.Hata, H.Nakashima and N.Tsuji
Phil. Mag., Vol.90 (2010), Issue 34, pp.4475-4488.
- "Mechanical Properties and Crash Worthiness of Ultrafine Grained Multi-Phase Steel Sheets"
Yoshitaka Okitsu, Tadashi Naito, Naoki Takaki, Tomoaki Sugiura and Nobuhiro Tsuji
SAE Int. J. Mater. Manuf., Volume 3, No.1 (2010), pp.237-245.
- "Quantification of Internal Dislocation Density Using Scanning Transmission Electron Microscopy in Ultrafine Grained Pure Aluminum Fabricated by Severe Plastic Deformation"
Y.Miyajima, M.Mitsuhara, S.Hata, H.Nakashima and N.Tsuji
Mater. Sci. Eng. A, 528 (2010), pp.776-779.
- "Cu/Zr Nanoscaled Multi-Stacks Fabricated by Accumulative Roll Bonding"
Y.F.Sun, N.Tsuji, H.Fujii and F.S.Li
J. Alloys Comp., 504 (2010), S443-S447.
- "Formation of Bimodal Grain Structures in High Purity Al by Reversal High Pressure Torsion"
Dmitry Orlov, Yoshikazu Todaka, Minoru Umemoto and Nobuhiro Tsuji
Scripta Mater., Vol.64, No.6 (2011), pp.498-501.
- "Annealing Behavior of Solution Treated and Aged Al-0.2wt%Sc Deformed by ARB"
E.Borhani, H.R.Jafarian, H.Adachi, D.Terada and N.Tsuji
Mater. Sci. Forum, 667-669 (2011), pp.211-216.
- "Martensitic Transformation from Ultrafine Grained Austenite Fabricated by ARB in Fe-24Ni-0.3C"
H.R.Jafarian, E.Borhani, A.Shibata, D.Terada and N.Tsuji
Mater. Sci. Forum, 667-669 (2011), pp.361-366.
- "High-Temperature Severe Plastic Deformation of Ferritic Steel by Torsion"
A.Setiawan, D.Terada and N.Tsuji
Mater. Sci. Forum, 667-669 (2011), pp.403-408.
- "Development of Textured Coated Superconductor Substrate Tapes by Severe Plastic Deformation Processing"
P.P.Bhattacharjee and N.Tsuji
Mater. Sci. Forum, 667-669 (2011), pp.1189-1194.
- "Dynamic Deformation Behavior of Ultrafine Grained Iron Produced by Accumulative Roll Bonding and Annealing"
Y.Okitsu, N. Takata, N.Tsuji
Scripta Mater., Vol. 64 (2011), pp.896-899.
- "Development of Highly Cube Texture Nickel Superconductor Substrate Tapes by Accumulative roll Bonding (ARB)"
P.P.Bhattacharjee and N.Tsuji
Int. J. Mater. Res., Vol. 102 (2011), pp.173-182.
- "Effect of Al additions on the age hardening response of the Mg-2.4Zn-0.1Ag-0.1Ca (at.%) alloy - TEM and 3DAP study"
C. L. Mendis, K. Oh-ishi, and K. Hono
Mat. Sci. Eng. A. Vol. 527 (2010), pp.973.
- "Effect of Zr addition on the mechanical properties of as-extruded Mg-Zn-Ca-Zr alloys"
T. Honma, C. L. Mendis, K. Hono and S. Kamado
Mat. Sci. Eng. A, Vol. 527 (2010), pp.2356 - 2362.
- "Effect of Ga addition on the microstructure and magnetic properties of hydrogenation-disproportionation-desorption-recombination processed Nd-Fe-B powder"
H. Sepehri-Amin, W. F. Li, T. Ohkubo, T. Nishiuchi, S. Hirosawa, and K. Hono
Acta Mater., Vol. 58 (2010), pp.1309-1316.
- "Towards the development of heat treatable high strength wrought Mg alloys"
K. Hono, C. L. Mendis, T. T. Sasaki, and K. Oh-ishi
Scripta Mater., Vol. 63 (2010), pp.710 - 715.
- "Enhanced precipitation hardening of Mg-Ca alloy by Al addition"
J. Jayaraj, C. L. Mendis, T. Ohkubo, K. Oh-ishi and K. Hono
Scripta Mater., Vol. 63 (2010), pp.710 - 715.
- "Coercivity enhancement of HDDR-processed Nd-Fe-B permanent magnet by rapid hot-press consolidation process"
N. Nozawa, H. Sepehri-Amin, T. Ohkubo, K. Hono, T. Nishiuchi, and S. Hirosawa
J. Mag. Mag. Mater., Vol. 323 (2010), pp.115-121.
- "High coercivity FePt-C bulk magnets processed by spark plasma sintering and hot-deformation"
R. Gopalan, T. Ohkubo, and K. Hono
J. Mag. Mag. Mater., Vol. 322 (2010), pp.3423-3427.
- "Coercivity enhancement of hydrogenation-disproportionation-desorption-recombination processed Nd-Fe-B powders by the diffusion of Nd-Cu eutectic alloy"
H. Sepehri-Amin, T. Ohkubo, T. Nishiuchi, S. Hirosawa and K. Hono
Scripta Mater., Vol. 63 (2010), pp.1124 - 1127.
- "Precipitation of prismatic plates in Mg-0.3Ca alloys with In additions"
C. L. Mendis, K. Oh-ishi, T. Ohkubo, and K. Hono
Scripta Mater. Vol. 64 (2011), pp.137 - 140.
- "Strain distribution in freestanding Si/SixNy membranes studied by transmission electron microscopy"
H. Gao, K. Ikeda, S. Hata, H. Nakashima, D. Wang, H. Nakashima
Thin Solid Films, Vol. 518 (2010), pp.6787-6791.
- "Microstructure and strain distribution in freestanding Si membrane strained by SixNy deposition"
H. Gao, K. Ikeda, S. Hata, H. Nakashima, D. Wang, H. Nakashima
Materials Science and Engineering A, Vol. 527 (2010), pp.6633-6637.
- "Measurement of strain in freestanding Si/SixNy membrane by convergent beam electron diffraction and finite element method"
H. Gao, K. Ikeda, S. Hata, H. Nakashima, D. Wang, H. Nakashima
Japanese Journal of Applied Physics, Vol. 49 (2010), 090208 (Rapid communication, 3 pages).
- "Ordering transformations in Ni75Mo15Mn10 alloy"
U. D. Kulkarni, S. Hata, M. Mitsuhara, K. Ikeda
Transactions of The Indian Institute of Metals, Vol. 63, Issue 5 (2010), pp.819-822.
- "Fabrication of high strength Cu-NbC composite conductor by high pressure torsion"
B.D.Long, M.Umemoto, Y.Todaka, R.Othman, H.Zuhailawati
Materials Science and Engineering A, Vol.528, (2011), pp. 1750-1756.
- "Anomalous Property Evolution during Annealing in HPTed SUS 304 Austenitic Stainless Steel"
I.Shuro, M.Umemoto, Y.Todaka, H.H.Kuo, H.Wang
Materials Science Forum, Vols.667-669, (2011), pp. 589-592.
- "Effect of Si content on fracture behaviour change by strain rate in Si steels"
T.Mizuguchi, R.Oouchi, R.Ueji, Y.Tanaka and K.Shinagawa
Mater. Sci. Forum, Vols.654-656 (2010), pp.1303-1306.
- "Stress-induced Martensitic Transformation Behaviors at Various Temperatures and their TRIP Effects in SUS304 Metastable Austenitic Stainless Steel"
N.Tsuchida, Y.Morimoto, T.Tonan, Y.Shibata, K.Fukaura and R.Ueji
ISIJ International, 51 (2011), pp.124-129.
- "Evaluation of the block boundary and sub-block boundary strengths of ferrous lath martensite using a micro-bending test"
A. Shibata, T. Nagoshi, M. Sone, S. Morito, Y. Higo
Mater. Sci. Eng. A, 527 (2010), pp.7538-7544.
【A01イ】
- ""
H.Ushida, S.Ogata, H.Kimizuka
, Vol.60 (2011), Issue 1, pp.71-78.
- "Effect of Temperature on Fast Hydrogen Diffusion in Iron: A Path-Integral Quantum Dynamics Approach"
H.Kimizuka, H.Mori and S.Ogata
Phys. Rev. B, Vol.83 (2011), in press.
- "Microscopic Phase-Field"
H.Mori, H.Kimizuka, S.Ogata
, Vol.75 (2011), Issue 2, pp.104-109.
【A02ウ】
- "Application of High-Pressure Torsion for Consolidation of Ceramic Powders"
K. Edalati and Z. Horita
Scripta Materialia, 63, 174-177, (2010).
- "High-Pressure Torsion for Giant Magnetoresistance and Better Magnetic Properties"
S. Nishihata, K. Suehiro, M. Arita, M. Masuda and Z. Horita
Advanced Engineering Materials, 12, 793-797, (2010).
- "Influence of grain size on the density of deformation twins in Cu-30%Zn alloy"
Y. Li, Y.H. Zhao, W. Liu, C. Xu, Z. Horita, X.Z. Liao, Y.T. Zhu, T.G. Langdon and E.J. Lavernia
Materials Science and Engineering A, 527, 3942-3948, (2010).
- "The role of stacking fault and twin boundaries in grain refinement of a Cu-Zn alloy processed by high-pressure torsion"
Y.B. Wang, X.Z. Liao, Y.H. Zhao, E.J. Lavernia, S.P. Ringer, Z. Horita, T.G. Langdon and Y.T. Zhu
Materials Science and Engineering A, 527, 4959-4966, (2010).
- "Effect of Equal Channel Angular Pressing on the Pitting Corrosion Resistance of Aluminum-Copper Alloy"
I.J. Son, H. Nakano, S. Oue, S. Kobayashi, H. Fukushima and Z. Horita
Surface Technology, 61, 50-57, (2010).
- "Continuous High-Pressure Torsion"
K. Edalati and Z. Horita
Journal of Materials Science, 45, 4578-4582, (2010).
- "Ultrahigh Strength of Nanocrystalline Iron-Based Alloys Produced by High Pressure Torsion"
T. Furuta, S. Kuramoto, K. Horibuchi, T.Ohsuna and Z. Horita
Journal of Materials Science, 45, 4745-4753, (2010).
- "Effect of high-pressure torsion processing and annealing on hydrogen embrittlement of type 304 metastable austenitic stainless steel"
Y. Mine, K. Tachibana and Z. Horita
Metallurgical and Materials Transactions A, 41, 3110-3120, (2010).
- "Cold Consolidation of Ball-Milled Titanium Powders Using High-Pressure Torsion"
K. Edalati, Z. Horita, H. Fujiwara and K. Ameyama
Metallurgical and Materials Transactions A, 41, 3308-3317, (2010).
- "Hydrogen trapping on lattice defects produced by high-pressure torsion in Fe-0.01 mass% C alloy"
Y. Mine, T. Tsumagari and Z. Horita
Scripta Materialia, 63, 552-555, (2010).
- "Correlations between Hardness and Atomic Bond Parameters of Pure Metals and Semi-metals after Processing by High-Pressure Torsion"
K. Edalati. and Z. Horita
Scripta Materialia, 64, 161-164, (2011)
- "Fabrication of ultrafine-grained Ti-(5-50wt.%)Al2O3 composites using high-pressure torsion"
K. Edalati, H. Iwaoka, Z. Horita, M. Tanaka, K. Higashida, H. Fujiwara, and K. Ameyama
Kovov? materi?ly. 49, 85-92, (2011)
- "High-Pressure Torsion of Pure Magnesium: Evolution of Mechanical Properties, Microstructures and Hydrogen Storage Capacity with Equivalent Strain"
K. Edalati, A. Yamamoto, Z. Horita and T. Ishihara
Scripta Materialia, 64, 880-883, (2011).
- "Nanocrystalline Zr3Al Made through Amorphization by Repeated Cold Rolling and Followed by Crystallization"
D. Geist, S. Ii, K. Tsuchiya, H.P. Karnthaler, G. Stefanov, C. Rentenberger
J. Alloys Comp., 509(2011)1815-1818.
- "Effects of Nano / Meso Harmonic Microstructure on Mechanical Properties in Austenitic Stainless Steel Produced by MM / HRS Process"
H. Fujiwara, H. Tanaka, M. Nakatani and K. Ameyama
Mater. Sci. Forum, Vols. 638-642 (2010), pp. 1790-1795.
- "New Microstructure Design for Commercially Pure Titanium with Outstanding Mechanical Properties by Mechanical Milling and Hot Roll Sintering"
T. Sekiguchi, K. Ono, H. Fujiwara and K. Ameyama
Mater. Trans., Vol. 51 (2010), pp. 39-45.
- "Effect of Alumina Content on the Mechanical Properties of Alumina Particle Dispersion Magnesium"
S. Kawamori, K. Kuroda, Y. Kasuga, M. Yokouchi, H. Fujiwara and K. Ameyama
Mater. Trans., Vol. 51 (2010), pp. 1893-1900.
- "Formation of Amorphous Fe-Cr-P-C Alloy Coating Films by Thermal Spraying Technique"
M. Komaki, T. Mimura, Y. Kusumoto, R. Kurahasi, M. Kouzaki and T. Yamasaki
Materials Transactions, 51, (2010), 1581-1585.
- "Microstructure and mechanical properties of AZ61 Mg alloy prepared by multi directional forging"
H.Miura, G. Yu, X.Yang, T.Sakai
Transactions of nonferrous metals society of china,Vol. 20 (2010), pp. 1294-1298.
- "Nano-grain evolution in austenitic stainless steel during multi-directional forging"
Y.Nakao, H. Miura
Materials Science Engineering A 528 (2011), pp. 1310-1317.
- "Production of recrystallized nano-grains in a fine-grained Cu-Zn alloy"
H.Miura, T.Sakai, S. Maruoka and J.J. Jonas
Philo. Mag. Lett., Vol.90, No. 2, February (2010), pp. 93-101.
- "Static recrystallization behavior of hot-deformed magnesium alloy AZ31 during isothermal annealing"
Yang Xu-yue, Zhu Ya-Kum, H. Miura and T. Sakai
Transactions of nonferrous metals society of china Vol. 20 (2010), pp1269-1274.
【A02エ】
- "Bending-Drawing Process to Manufacture the Ultrafine Copper Wire with Excellent Electrical and Mechanical Properties"
J. Yanagimoto, J. Tokutomi, K. Hanazaki and N. Tsuji
Annals of the CIRP, Vol.60-1(2011), in press
- "Effect of Ti Addition on Tensile Properties of C-Mn Steels Subjected to ECAE and Heat Treatment"
A. Yanagida, K. Okazaki, K. Ishikawa and A. Azushima
Steel Research International, 81(2010), 462-465.
- "Stress-Induced Martensitic Transformation Behaviors at Various Temperatures and Their TRIP Effects in SUS304 Metastable Austenitic Stainless Steel"
N.Tsuchida, Y.Morimoto, T.Tonan, Y.Shibata, K.Fukaura and R.Ueji
ISIJ International, Vol.51 (2011), pp.124-129.
【A03オ】
- "Inverse Temperature Dependence of Activation Volume in Ultrafine-Grained Copper Processed by Accumulative Roll-Bonding"
T. Kunimine, T. Aragaki, T. Fujii, S. Onaka and M. Kato
J. Mater. Sci. (2011, in press).
- "Effects of Si Addition on Mechanical Properties of Copper Severely Deformed by Accumulative Roll-Bonding"
T. Kunimine, T. Fujii, S. Onaka, N. Tsuji and M. Kato
J. Mater. Sci. (2011, in press).
- "Low-Cycle Fatigue of Ultrafine-grained Aluminum at Low Temperatures"
Y. Nakanishi, T. Fujii, S. Onaka and M. Kato
Mater. Trans. (2011, in press).
- "Effect of ausforming on nanobainite steel"
W.Gong, Y.Tomota, M.S.Koo and Y.Adachi
Scr. Mater., Vol.63 (2010), issue 8, pp.819-822.
- "Tensile Behavior of a TRIP-Aided Ultra-fine Grained Steel Studied by Neutron Diffraction"
K.Asoo, Y.Tomota, S.Harjo and Y.Okitsu
ISIJ Int., Vol.51 (2011), No.1, pp.145-150.
- "Comparative Analysis of Inhomogeneous Plastic Flow in Bulk and Ribbon Metallic Glasses Monitored by Acoustic Emission"
A. Lazarev, A. Vinogradov and S. Hashimoto
J. Alloys and Compd., Vol. 504 (2010), Suppl. 1, pp.S60-S64.
- "On the shear bands velocity and detectability of acoustic emission in metallic glasses"
A. Vinogradov
Scr. Mater., Vol. 63 (2010), Issue 20, pp.89-92.
- "Propagation of shear bands in metallic glasses and transition from serrated to non-serrated plastic flow at low temperatures"
A. Vinogradov, A. Lazarev, D. V. Louzguine-Luzgin, Y. Yokoyama, S. Li, A. R. Yavari and A. Inoue
Acta. Mater. Vol.58 (2010), Issue 20, pp.6736-6743.
- "Deformation and Fracture Behavior of Metallic Glassy Alloys and Glassy-Crystal Composites"
D. Louzguine, A.Vinogradov, S.Li, A. Kawashima, G.Xie, A.R. Yavari and A.Inoue
Metal. Mater. Trans. A, Vol.41 (2010), Issue 7, pp.1664-1669.
- "The influence of temporary hydrogenation on ECAP formability and low cycle fatigue life of CP titanium"
A. Czerwinski, R. Lapovok, D. Tomus, D. Orlov, Y. Estrin and A. Vinogradov
J. Alloys and Compd., Vol.509 (2011), Issue 6, pp.2709-2715.
- "Reversible nature of shear bands in copper single crystals subjected to iterative shear of ECAP in forward and reverse directions"
H. Miyamoto, T. Ikeda, T. Uenoya, A. Vinogradov and S. Hashimoto
Mater. Sci. Eng. A, Vol.528 (2011), Issue 6, pp.2602-2609.
- "Nanostructurization assisted by twinning during Equal Channel Angular Pressing of Metastable 316L Stainless Steel"
H.Ueno, K. Kakihata, Y.Kaneko, S.Hashimoto and A.Vinogradov
J. Mater. Sci., (2011, in press).
- "Characterization of Crack-tip Dislocations and Their Effects on Materials Fracture"
K. Higashida, M. Tanaka, S. Sadamatsu
Mater. Sci. Forum, Vol.654-656 (2010), pp.2307-2311.
- "Crack tip dislocations observed by combining scanning transmission electron microscopy and computed tomography"
S. Sadamatsu, M. Tanaka, K. Higashida, K. Kaneko, M. Mitsuhara, S. Hata, M. Honda
Adv. Mater. Res. 89-91 (2010), pp.473-478.
- "High pressure torsion of pure Ti: Effect of pressure and strain on allotropy"
K. Edalati, Z. Horita, M. Tanaka, K. Higashida
Adv. Mater. Res. 89-91 (2010) pp.171-176.
- "Strengthening mechanisms and optimization of structure and properties in a nanostructured IF steel"
X.Huang, N.Kamikawa and N.Hansen
J. Mater. Sci., Vol.45 (2010), No.17, pp.4761-4769.
【A03カ】
- "Asymmetric ability of grain boundaries to generate dislocations under tensile or compressive loadings"
T. Shimokawa
Phys. Rev. B, Vol.82 (2010), 174122.
Proceeding Papers
【A01ア】
- "Recrystallization or Not ?: Formation Mechanism of Ultrafine Grains in Aluminum through Severe Plastic Deformation and Subsequent Annealing"
N.Tsuji and N.Kamikawa
Proc. of ICAA 12, The Japan Institute of Light Metals (2010), pp.1134-1140.
- "Microstructural Change Resulting from Aging Treatment of Ultrafine Grained Al-Si Alloy Fabricated by ARB"
K.Nakagawa, T. Kanadani, N. Tsuji, D. Terada, T. Masui, and Y. Sato
Proc. of ICAA 12, The Japan Institute of Light Metals (2010), pp.1083-1088.
- "Effect of Pre-aging on Microstructure and Mechanical Property of Al-0.2wt% Sc Deformed by ARB"
E.Borhani, H. Jafarian, T. Sato, D. Terada, Y. Miyajima, and N. Tsuji
Proc. of ICAA 12, The Japan Institute of Light Metals (2010), pp.2168-2173.
- "Evolution of the Microstructure of a {100} <001> Pure Aluminum Single Crystal during Severe Plastic Deformation"
K.Kashihara, W. Ikushima, Y. Miyajima, D. Terada, and N. Tsuji
Proc. of ICAA 12, The Japan Institute of Light Metals (2010), pp.2130-2135.
- "Quantitative Analysis of Local Deformation in Dual Phase Steel during Tensile Test by Digital Image Correlation"
M.Wadamori, D.Terada and N.Tsuji
Proc. MS&T 2010 (2010), pp.1981-1987.
- "Phase Transformation from Ultra-Fine Grained Austenite in a Medium Carbon Steel"
S.Daido, D.Terada, A.Shibata and N.Tsuji
Proc. MS&T 2010 (2010), pp.1954-1959.
- "Ways to Manage Both Strength and Ductility in Nanostructured Steels"
N.Tsuji
Proc. of Int. Conf. on Advanced Steels 2010 (ICAS 2010), Edited by Yuqing WENG, Han DONG, and Yong GAN, Metallurgical Industry Press, pp.110-120.
- "Strength and Electrical Conductivity of Ultrafine Grained Cu Fabricated by Giant Straining Process"
N.Tsuji, N.Takata, S.H.Lee and K.Hanazaki
Extended abstract book of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM 2010), 2 pages.
- "Advances in laser assisted 3D atom probe and its applications to light metals"
K. Hono, K. Oh-ishi, C. L. Mendis, and T. Ohkubo
Proc. of ICAA 12, The Japan Institute of Light Metals (2010), pp..
- "Precipitation hardenable Mg-Ca-Al alloys"
J. Jayaraj, C. L. Mendis, K. Oh-ishi, K. Hono
Magnesium Technology 2010, Editor(s): Eric Nyberg, Sean Agnew, Neale Neelameggham, Mihriban Pekguleryuz, TMS annual meeting 2010
- "Mechanical properties and microstructures of twin roll cast Mg-2.4Zn-0.1Ag-0.1Ca-0.16Zr alloy"
C.L. Mendis, J. H. Bae, N.J. Kim, and K. Hono
Magnesium Technology 2010, Editor(s): Eric Nyberg, Sean Agnew, Neale Neelameggham, Mihriban Pekguleryuz, TMS annual meeting 2010.
- "Dislocation electron tomography of boundaries in deformed aluminum"
A. Ramar, S. Hata, X. Huang, R. E. Dunin-Borkowski, G. Winther
Proc. 31st Riso International Symposium on Materials Science: Challenges in materials science and possibilities in 3D and 4D characterization techniques, Eds. N. Hansen, D. J. Jensen, S. F. Nielsen, H. F. Poulsen and B. Ralph, Riso National Laboratory for Sustainable Energy, Technical University of Denmark (2010), pp.397-404.
- "Development of 3D TEM imaging techniques using diffraction contrast"
S. Hata, M. Mitsuhara, M. Tanaka, K. Kaneko, K. Higashida, K. Ikeda, H. Nakashima, T. Daio, S. Matsumura
Proc. The 17th International Microscopy Congress (IMC17) (2010), 2 pages.
- "Three-dimensional evaluation of dislocation arrangements using electron tomography in austenitic steel"
M. Mitsuhara, S. Hata, K. Ikeda, H. Nakashima, M. Tanaka, K. Higashida
Proc. 31st Riso International Symposium on Materials Science: Challenges in materials science and possibilities in 3D and 4D characterization techniques, Eds. N. Hansen, D. J. Jensen, S. F. Nielsen, H. F. Poulsen and B. Ralph, Riso National Laboratory for Sustainable Energy, Technical University of Denmark (2010), pp.353-360.
- "Microstructure and strain distribution in strained freestanding Si membrane"
H. Y. Gao, K, Ikeda, S. Hata, H. Nakashima, D. Wang, H. Nakashima
Proc. The 17th International Microscopy Congress (IMC17) (2010), 2 pages.
- "Strain induced transformation and annealing behavior of SUS304 stainless steel processed by HPT"
M.Umemoto, I.Shuo, H.C.Wang, Y.Todaka, H.H.Kuo
Extended abstract book of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM 2010), 2 pages.
- "Hydrogen embrittlement behavior of bulk nanostructured pure Fe produced by high-pressure torsion straining"
Y.Todaka, K.Morisako, Y.Matsumoto, R.Ueji, Y.Nagaki, M.Umemoto
Extended abstract book of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM 2010), 2 pages.
- "A comparative study of the annealing behavior of HPTed austenitic stainless steels"
I.Shuro, H.C.Wang, M.Umemoto, H.H.Kuo, Y.Todaka
Extended abstract book of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM 2010), 2 pages.
- "Characterization of local deformation behavior of martensitic steel using a micro-sized cantilever-beam specimen"
A. Shibata, T. Nagoshi, M. Sone, S. Morito, Y. Higo
Proc. 31st Riso International Symposium on Materials Science: Challenges in materials science and possibilities in 3D and 4D characterization techniques, Eds. N. Hansen, D. J. Jensen, S. F. Nielsen, H. F. Poulsen and B. Ralph, Riso National Laboratory for Sustainable Energy, Technical University of Denmark (2010), pp.429-436.
- "Micromechanical characterization of boundary strength in martensitic steel"
A. Shibata, T. Nagoshi, M. Sone, S. Morito, Y. Higo
Proc. MS&T 2010 (2010), pp.1954-1959.
- "Local deformation behavior of Fe-Ni lenticular martensite"
L. Zhang, T. Ohmura, K. Tsuzaki, A. Shibata
Proc. of Int. Conf. on Advanced Steels 2010 (ICAS 2010), Edited by Yuqing WENG, Han DONG, and Yong GAN, Metallurgical Industry Press, FR056.
【A01イ】
- "First-Principles Study of the Bonding and Mechanical Properties of Metallic Grain Boundaries"
M. Kohyama, S. Tanaka, R.Z. Wang, Y. Shiihara, S. Saitou, T. Tamura and S. Ishibashi
Proceedings of 12th International Conference on Aluminum Alloys (ICAA12), The Japan Institute of Light Metals (2010)
- "First-principle Constitutive Equation for Nonlinear Elasticity"
S.Ogata and H.Kimizuka
2010 Materials Research Society (MRS) Fall Meeting Abstracts, #P10.35, 1 page.
- "Microscopic Phase Field Study of Hydrogen Transport by Dislocation in BCC Iron"
H.Mori, Y.Takenaka, H.Kimizuka and S.Ogata
2010 Materials Research Society (MRS) Fall Meeting Abstracts, #P10.43, 1 page.
- "Quantum Dynamics Study of Hydrogen Diffusion in Iron with Lattice Defects"
H.Kimizuka, H.Mori and S.Ogata
Proceedings of the Fifth International Conference on Multiscale Materials Modeling (MMM2010), p.701, 1 page.
【A02ウ】
- "High Strength and Ductility in Ball-Milled Titanium Powders Consolidated by High-Pressure Torsion"
K. Edalati, Z. Horita, H. Fujiwara, K. Ameyama, M. Tanaka and K. Higashida
Materials Science Forum, 654-656, 1239-1242, (2010).
- "Aging Behavior of Al-Li-Cu-Mg Alloy Processed by High-Pressure Torsion"
S. Lee, D. Akama, Z. Horita, T. Masuda, S. Hirosawa and K. Matsuda
Materials Science Forum, 654-656, 1243-1246, (2010).
- "Severe Plastic Deformation under High-Pressure for Production of Multifunctional Properties"
Z. Horita
Proceedings of International Symposium on Giant Straining Process for Advanced Materials (GSAM2010) "Production of Mutifunctional Materials Using Severe Plastic Deformation" edited by Z. Horita, Kyushu University Press, Fukuoka (2011), p.1-4.
- "High-Pressure Torsion for Ring Samples in Different Thicknesses"
H. Iwaoka, Y. Harai and Z. Horita
Materials Science Forum, 667-669, 51-56, (2011).
- "Application of High-Pressure Sliding for Grain Refinement of Al and Mg Alloys"
K.Tazoe, S. Honda and Z. Horita
Materials Science Forum, 667-669, 91-96, (2011).
- "Aging Behavior of Al-Mg-Si Alloys Processed by High-Pressure Torsion"
D. Akama, Z. Horita, K. Matsuda and S. Hirosawa
Materials Science Forum, 667-669, 259-264, (2011).
- "Aging Behavior of Cu-Ni-Si Alloy Processed by High-Pressure Torsion"
H. Matsunaga, Z. Horita, K. Imamura, T. Kiss and X. Sauvage
Materials Science Forum, 667-669, 307-312, (2011).
- "Annealing Behavior of FeNi Alloy Processed by High-Pressure Torsion"
S. Lee and Z. Horita
Materials Science Forum, 667-669, 313-318, (2011).
- "Correlation of Physical Parameters with Steady-State Hardness of Pure Metals Processed by High-Pressure Torsion"
K. Edalati and Z. Horita
Materials Science Forum, 667-669, 683-688, (2011).
- "Mechanical Properties of Al-6061 and an Al-6061 Metal Matrix Composite Processed by High-Pressure Torsion"
C. Xu, Z. Horita and T. G. Langdon
Materials Science Forum, 667-669, 689-694, (2011).
- "Nanostructure Formation and Amorphization in Intermetallic Compounds by Severe Plastic Deformation" (invited)
K. Tsuchiya and O. Ciuca
Materials Science Forum, Vols. 667-669 (2011) pp 17-24.
- "Effect of Grain Refinement by SPD on Elastic Properties of TiNi"
K. Tsuchiya, Q. Mei, L. Zhang, T. Ohmura
Proceedings of International Symposium on Giant Straining Process for Advanced Materials (GSAM2010) "Production of Mutifunctional Materials Using Severe Plastic Deformation" edited by Z. Horita, Kyushu University Press, Fukuoka (2011), p.84-87.
- "Microwave Heating Behavior of Fine Stainless Steel Powders in H-Field at 2.45 GHz"
H. Fujiwara, S. Toyota, L. Anggraini, K. Ameyama and D. Agrawall
Proc. International Microwave Power Institute's 44th annual symposium, (2010), pp. 79-82.
- "Creation of Harmonic Structured Materials with Outstanding Mechanical Properties"
K. Ameyama, H. Fujiwara, T. Sekiguchi, Sabrina N.B.R., M. Rifai
Proceedings of International Symposium on Giant Straining Process for Advanced Materials (GSAM2010) "Production of Mutifunctional Materials Using Severe Plastic Deformation" edited by Z. Horita, Kyushu University Press, Fukuoka (2011), p.80-83.
- "Strain Hardening and Fracture Behavior of SUS304L and SUS316L Austenitic Stainless Steel Compacts with Harmonic Microstructure"
M. Rifai, H. Tanaka, Z. Zhang, H. Fujiwara and K. Ameyama
International Symposium on Giant Straining Process for Advanced Materials (GSAM2010).
- "High Strength and High Ductility in Electrodeposited Nanocrystalline Ni-W Alloy"
K. Fujita, T. Suidu and T. Yamasaki
Materials Science Forum, Vol. 654-656 (2010), 1118-1121.
- "Viscous Flow Behaviour of Supecooled Liquids and Mechanical Properties in Zr-Cu-Ni-Al Bulk Metallic Glasses"
T. Yamasaki, M. Yamada, T. Mori, T. Kikuchi, Y. Yokoyama, A. Inoue and D. H. Kim
Materials Science Forum, Vol. 654-656 (2010), 1046-1049.
- "Formation of Nanocrystalline Ni-W Alloys by Electrodeposition and Their Mechanical Proeprties"
Tohru Yamasaki and Kazutaka Fujita
Proceedings of International Symposium on Giant Straining Process for Advanced Materials (GSAM2010) "Production of Mutifunctional Materials Using Severe Plastic Deformation" edited by Z. Horita, Kyushu University Press, Fukuoka (2011), p.34-37.
- "Multi directional forging of AZ91Mgalloy and the specific mechanical properties"
H.Miua, X.Yang and T.Sakai
Proceedings of International Symposium on Giant Straining Process for Advanced Materials (GSAM2010) "Production of Mutifunctional Materials Using Severe Plastic Deformation" edited by Z. Horita, Kyushu University Press, Fukuoka (2011), p.64-67.
- "Grain refinement of coarse grained gold by combined thermo-mechanical process of severe plastic deformation and low temperature annealing"
H.Miura, I.Itabashi, G..u and T. Sakai
Proceedings of 15th international conference on the strength of materials(ICSMA-15), Journal of physics :conference series 240 (2010).
- "Improvement of mechanical properties of AZ91Mg alloy by multi -directional forging and ultra grain refinement"
H.Miura and H.Liu
Abstract Book of Materials science and engineering, MSE2010, Abstracts MSEwebpp, Aug 24-26, 2010. Darmstadt Germany.
- "Nano-SiO2 particles reinforced Magnesium alloy produced by friction stir processing"
Yupei Jiang, Xuyue Yang, H.Miura, and T.Sakai
Proceedings of the sixth international conference on physical and numerical simulation of materials processing (CD ver.), ICPNS2010, November16-19,2010,Guilin, China.
- "Grain Refinement in the surface layer of AZ31 Mg alloy sheet processed by cyclic bending"
Lei Zhang, Xuyue Yang, H.Miura and T.Sakai
Proceedings of the sixth international conference on physical and numerical simulation of materials processing (CD ver.), ICPNS2010, November16-19,2010,Guilin, China.
- "Microstructure and mechanical properties of the ultrafine-grained SUS304 produced by multi directional forging"
Y.Iwabuchi and H.Miura
Abstract book of international symposium on giant straining process for advanced materials, GSAM2010, November19-22, 2010, Fkuoka, Japan.
- "Effect of strain rate on microstructural change during multi directional forging of AZ61 magnesium alloy"
K.Matsumoto and H.Miura
Abstract book of international symposium on giant straining process for advanced materials, GSAM2010, November19-22, 2010, Fkuoka, Japan.
- "Mechanisms of Dynamic Recrystallization in Cu-Sn-P Alloy"
H.Miura, M. Watanabe, T. Shirai, and A. Ishibashi
Materials Science Forum, Vols.654-656 (2010), pp.1267-1270.
- "Nano-grained structure induced by mechanical twinning during multi-directional forging and the mechanical properties"
H.Miura and Y.Nakao
Materials Science Forum, Vols.633-634 (2010), pp.577-593
- "Ultrafine grain evolution in copper alloys induced by mechanisms of continuous dynamic and static recrystallization"
H.Miura and T.Sakai
Materials Science Forum, Vols.638-642 (2010), pp.1983-1988.
- "Dynamic recrystallization Behaviour in Cu-Sn-P alloy for high strength copper tube"
Masao Watanabe, Takashi Shirai, Akihiko Ishibashi and Hiromi Miura
Materials Science Forum, Vol.654-656 (2010), pp.1271-1274.
- "Mechanisms of ultrafine grain formation in severe plastic deformation"
T. Sakai and H. Miura
Materials Science Forum, Vols.638-642 (2010), pp.98-103.
【A02エ】
- "Optimum Pass Design of Bar Rolling for Producing Bulk Ultrafine-grained Steel by Numerical Simulation"
T.Inoue
Materials Science Forum on The 7th Pacific Rim International Conference on Advanced Materials and Processing (PRICM 7), 6 pages, Vol.654-656 (2010), pp.1561-1564.
- "Macro-micro Combined Texture Evolution Model for Hot Strip with High Reduction Rolling"
T. Morimoto, J. Yanagimoto, F. Yoshida, Y. Kasumoto and O. Akisue
Proceeding of the 10th International Conference on Steel Rolling, (2010), 1 page, pp.151.
【A03オ】
- "Role of Dislocations Emitted from Grain Boundaries on Plastic Deformation of Ultrafine-Grained Materials"
M. Kato, T. Kunimine, T. Fujii and S. Onaka
The 13th International Conference on Intergranular and Interphase Boundaries in Materials (iib2010) [JIMIC-7], Mie, Japan, 1page, 2010.
- "Effects of Si Addition on Mechanical Properties of Copper Severely Deformed by Accumulative Roll-Bonding"
T. Kunimine, T. Fujii, S. Onaka, N. Tsuji and M. Kato
The 13th International Conference on Intergranular and Interphase Boundaries in Materials (iib2010) [JIMIC-7], Mie, Japan, 1page, 2010.
- "Formation of Dislocation Structure during Cyclic Deformation of Ultrafine-Grained Aluminum at Low Temperatures"
Y. Nakanishi, T. Fujii, S. Onaka and M. Kato
The 12th International Conference on Aluminium Alloys (ICAA12),Yokohama, Japan, 6pages, 2010.
- "Microstructural Evolution Caused by Accumulative Roll-bonding of Cu (100)[001] Single Crystals"
A. Yoshida, Y. Miyajima, T. Fujii, S. Onaka and M. Kato
Extended Abstracts of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM2010), Fukuoka, Japan, 1 page, 2010.
- "Suppression of Grain Growth by Precipitation of Co-Fe Particles during Aging of an ECAPed Cu Alloy"
T. Sumiya, T. Fujii, H. Sato, Y. Watanabe, S. Onaka and M. Kato
Extended Abstracts of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM2010), Fukuoka, Japan, 1 page, 2010.
- "Transformation Strain and Texture Evolution during Diffusional Phase Transformation of Low Alloy Steels Studied by Neutron Diffraction"
P.G. Xu, Y. Tomota, T. Suzuki, T. Kamiyama, S.C. Vogel
The 6th Int. Conf. on Physical and Numerical Simulation of Material Processing, Guilin, China, 7 pages, 2010.
- "Multifunctional ultrafine grained CuCr alloys"
A. Vinogradov
Extended Abstracts of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM 2010), 4 pages.
- "Acoustic Emission Analysis of Fracture of Metallic Glasses"
A.Lazarev and A.Vinogradov
Progress in Acoustic Emission, Proc of Int. Symp. on Acoustic Emission (IAES-20), Kumamoto, Japan, 6 pages, 2010.
- "Dynamic Precipitation During Cyclic Deformation in Under Aged Al-4Cu Containing Al2Cu Precipitates"
W. Z. Han, A. Vinogradov and C. R. Hutchinson
The 12th International Conference on Aluminium Alloys (ICAA12), Yokohama, Japan, 2010.
- "Evolution of Internal Stress During Cyclic Deformation of Al-4Cu as a Function of ' Precipitate State"
W. Z. Han, A. Vinogradov and C. R. Hutchinson
The 12th International Conference on Aluminium Alloys (ICAA12), Yokohama, Japan, 2010.
- "Crack tip dislocations observed by electron tomotraphy in single crystal silicon"
M. Tanaka, K. Higashida, S. Sadamatsu, H. Nakamura
Proceedings of the 31st Ris? International Symposium on Materials Science: Challenges in materials science and possibilities in 3D and 4D characterization techniques, Ris?-DTU, Denmark, 6 pages, 2010.
- "The increase in toughness at low temperature by severe plastic deformation"
K. Higashida, M. Tanaka, and T. Shimokawa
Extended Abstracts of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM 2010), 4 pages.
- "Dislocation-source hardening in nanostructured steel produced by severe plastic deformation"
N.Kamikawa, X.Huang and N.Hansen
Materials Science Forum, Vol. 638-642 (2010), 1959-1964. Proceedings of the International Conference on Processing and Manufacturing of advanced materials (Thermec'2009), 5 pages, 2010.
- "Recrystallization or not ? : Formation mechanism of ultrafine grains in aluminum through severe plastic deformation and subsequent annealing"
N.Tsuji and N.Kamikawa
The 12th International Conference on Aluminium Alloys (ICAA12), Yokohama, Japan, 7 pages, 2010.
【A03カ】
- "Formation mechanism of grain boundaries under severe plastic deformation by atomic simulations"
T. Shimokawa
Extended abstract book of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM 2010), 1 page.
- "The increase in toughness at low temperatures by severe plastic deformation"
K. Higashida, M. Tanaka, and T. Shimokawa
[1] Extended abstract book of the Int. Symp. on Giant Straining Process for Advanced Materials (GSAM 2010), 2 pages.
- "Modeling of Static Recrystallization and Nucleus Growth Simulation Considering Nucleation Incubation Period and Critical Nucleus Radius"
M. Muramatsu, Y. Aoyagi and K. Shizawa
CD-ROM of The 16th International Conference on Crystal Growth (ICCG-16), 1 page.
- "Modeling Hardening Characteristics of Metallic Materials under Impact Loading based on Field Theory of Multiscale Plasticity"
Y. Aoyagi and T. Hasebe
Abstracts of International Symposium on Explosion, Shock wave and High-energy reaction Phenomena 2010 (3rd ESHP Symposium), 1 page.
- "Crystal Plasticity Simulation on Stress Corrosion Cracking Considering Oxygen Diffusion along Grain Boundary"
Y. Aoyagi, T. Igarashi and Y. Kaji
Nuclear Materials 2010 (NuMat 2010), 1 page.
- "Modeling and Simulation on Irradiated Material Based on Crystal Plasticity Considering Crystal Defect Induced by Irradiation"
Y. Aoyagi and Y. Kaji
Proceedings of Plasticity '11: the 16th International Symposium on Plasticity and Its Current Applications (Plasticity '11), 3 pages.
to pagetop